{"product_id":"dramm-threaded-pipe-cap-with-washer","title":"Dramm - Threaded Pipe Cap with Washer","description":"\u003ch2\u003eThreaded Pipe Cap with Washer\u003c\/h2\u003e\u003cp\u003eA threaded cap closes off a threaded outlet that is not in use so the rest of the system can be pressurised. Dramm lists it among the common components of a PolyRail and JetRain installation, where it caps a line end or an unused port. The cap is female threaded and ribbed on the outside for hand tightening, and it is supplied with the flat washer that forms the seal. Order it by the thread it screws onto, not by the size of the tubing behind that thread.\u003c\/p\u003e\u003cp\u003eOne choice on this page: Size, which is the pipe thread the cap has to seat on. 1\/2 in, 3\/4 in and 1 in cover the threaded fittings Dramm uses across its valve stations, manifolds, risers and line end fittings, so read the thread on the outlet you are capping and order to match. The cap is female, so it goes over a male thread. Keep the washer with the cap and make sure it is seated before you tighten, because the washer is the sealing face, not the thread. If the thing you are closing is the open end of a polyethylene lateral rather than a threaded port, that is a different job and Dramm closes it with a figure 8 clamp or an end fitting instead.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSize\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1\/2 in, 3\/4 in or 1 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eThread\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFemale, seats on a male pipe thread\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSealing washer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFlat washer supplied with every cap\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBody\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eRibbed for hand tightening\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eApplication\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eClosing a threaded outlet, port or riser on a Dramm irrigation system\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eConfigurations\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSize\u003c\/th\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e1\/2 in\u003c\/td\u003e\n\u003ctd\u003eVCAPT050\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3\/4 in\u003c\/td\u003e\n\u003ctd\u003eVCAPT075\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e1 in\u003c\/td\u003e\n\u003ctd\u003eVCAPT100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eCloses an unused threaded outlet so the line can be pressurised and tested.\u003c\/li\u003e\n\u003cli\u003eSupplied with its flat sealing washer, so nothing else has to be ordered to make the joint.\u003c\/li\u003e\n\u003cli\u003eFemale thread in 1\/2 in, 3\/4 in and 1 in to match the threaded fittings across Dramm valve stations and manifolds.\u003c\/li\u003e\n\u003cli\u003eRibbed body tightens by hand, so no wrench is needed on a plastic thread.\u003c\/li\u003e\n\u003cli\u003eListed by Dramm as a standard PolyRail and JetRain component.\u003c\/li\u003e\n\u003cli\u003eComes off again, so a capped port can be brought back into service without cutting plumbing.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eIdeal Applications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eCapping the threaded end of a PolyRail or JetRain supply line.\u003c\/li\u003e\n\u003cli\u003eBlanking an unused outlet on a valve station or multi-outlet manifold.\u003c\/li\u003e\n\u003cli\u003eClosing a riser during commissioning or pressure testing.\u003c\/li\u003e\n\u003cli\u003eTaking a bench out of production without replumbing the header.\u003c\/li\u003e\n\u003cli\u003eClosing a drained threaded outlet ahead of winter.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cem\u003eUse these with Dramm valve stations and multi-outlet manifolds, the thread adaptors that step a threaded outlet onto poly lateral line, and the figure 8 clamp that closes a 16mm PE line end.\u003c\/em\u003e\u003c\/p\u003e","brand":"Dramm","offers":[{"title":"1\/2 in","offer_id":52800844005687,"sku":"VCAPT050","price":1.12,"currency_code":"USD","in_stock":true},{"title":"3\/4 in","offer_id":52800844038455,"sku":"VCAPT075","price":1.3,"currency_code":"USD","in_stock":true},{"title":"1 in","offer_id":52800844071223,"sku":"VCAPT100","price":1.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/0341\/5863\/files\/P8060030-X5.jpg?v=1786150771","url":"https:\/\/www.blacklabelsupply.io\/products\/dramm-threaded-pipe-cap-with-washer","provider":"BLACK LABEL","version":"1.0","type":"link"}